Realtek RTL9201R Firmware 1.32.7 / 9.34.11

Stasiz escribió:

Excellent firmware. PERIPH_API for LCD is now supported. I successfully flashed the ShuoLe enclosure with BW LCD.
 

Did you flash it to 9201R? it wont select Firmware Bin for me with a 9201R plugged in



 

Shonk escribió:

Did you flash it to 9201R? it wont select Firmware Bin for me with a 9201R plugged in

Yes.
 
 
 

I think i know what the problem is some of my RTL9201R's have 2Mbit spi chips
this firmware is 452k so it needs 4Mbit though there's alot of FF's in the file so i may be able
to trim it down

Ok it can only trim down to 244 KB it wont flash to a 2Mbit SPI
I know a few of my pcb's have 8Mbit SPI's some 4Mbit some 2Mbit

I have checked my enclosures

Cofre Disco Duro x 5           4Mbit SPI          1.33.88 Firmware Flashable 4Mbit SPI (needs correct LCD.bin will test flashing one at some point)
UTHAI/ShuoLe U25N-L x 2 4Mbit SPI          1.34.29 Firmware Flashable 4Mbit SPI (needs correct LCD.bin)
UTHAI Q5 x 4                      2Mbit SPI          1.32.7 Firmware
UTHAI Q6 x 6                      2Mbit SPI          1.32.7 Firmware
UTHAI Q7 x 7                      2Mbit SPI          1.32.7 Firmware

I have just noticed i can extract the led.bin from spi dumps

its 0000 to 3FF0 its the first thing flashed to the SPI

I will do the Cofre Disco Duro and UTHAI/ShuoLe U25N-L led.bin's in a few mins

I have tested the extracted LED.bin's

Both work fine they also both work fine on the Cofre Disco Duro
it doesnt look quite as good on the Cofre Disco Duro though as it only has 2 RGB Led's 
instead of 5 on the UTHAI U25N-L

Cofre Disco Duro LED is a breathing effect CUSTOMIZED_LED = 41 00
UTHAI U25N-L LED is a wave effect CUSTOMIZED_LED = 41 02


 

Here's a copy of all i have for the RTL9201

MPtool_Lite v2.0.20.50509
MPtool_Lite_Mini v2.0.4.31218

Its setup out of the box to flash a Cofre Disco Duro
With 9.34.11 + UTHAI LED as its slightly nicer looking
and has Configs for UTHAI U25N-L but i dont use it as that Enclosure
came with a newer factory firmware so i just edited its SPI

Firmwares Included
1.32.7
9.34.11

LED Bins Included (With CUSTOMIZED_LED code in file name to be inserted into the ini)
If your enclosure led's are rgb you should be able to use any of these with the correct CUSTOMIZED_LED code inserted into the ini
if your led is not rgb you will just get no light until you flash with no led.bin and set the correct CUSTOMIZED_LED = 00 08 for example of a non RGB led

Cofre Disco Duro 9.32.74_LED_41_00
Cofre Disco Duro 1.33.88_LED_41_00
JEYI RTL9201 2280 LED_sleep_green_35_02_01
UTHAI U25N-L_LED_41_02

if your enclosure doesnt use a LED.bin e.g. CUSTOMIZED_LED = 08 00
make sure to untick flash LED BIN in View,File Select
and use the correct config with correct CUSTOMIZED_LED = whatever your device uses

It has the following Factory SPI Dumps for use with a CH341
Orico 25PW1 C3 1.32.7
Cofre Disco Duro 9.32.74
ShuoLe LCD 1.33.3
Cofre Disco Duro 1.33.88
UTHAI U25N-L 1.34.29

mega.nz/file/huoVQTxD#kOSLFNs_bPo2wcrrw_...QDM4avs_I2NwUAjVdt1I

oh something of note i have noticed
9.xx.xx firmware is debug enabled firmware (1.xx.xx with debug enabled in the firmware)
1.xx.xx is standard release

Burst Rate in say HD Tune Pro for example is alot slower on 9.xx.xx firmwares i have noticed this on 9.xx.xx firmware on RTL9201's RTL9210B's and RTL9220's